Lamb Components - Miscellaneous

Tubing Ends (photo of weld ends)

#2917 7/16-20RH weld end (4130) – (for 3/4" x .065 tubing)

$8.95 each

#2919 1/2-20RH weld end (4130) – (for 7/8" x .065 tubing)

$8.95 each

#2921 1/2-20RH weld end (4130) – (for 7/8" x .083 tubing)

$8.95 each

#2923 1/2-20RH weld end (4130) – (for 1" x .083 tubing)

$8.95 each

#2924 1/2-20LH weld end (4130) – (for 1" x .083 tubing)

$9.95 each

#2924A 5/8-18 weld end (4130) – (for 1-1/4" x .065 tubing)

$11.25 each

#2925 3/4-16RH weld end (4130) – (for 1-1/8" x .095 tubing)

$10.75 each

#2926 3/4-16LH weld end (4130) – (for 1-1/8" x .095 tubing)

$11.75 each

#2927 3/4-16RH weld end (4130) – (for 1-1/4" x .095 tubing)

$13.95 each

#2928 3/4-16LH weld end (4130) – (for 1-1/4" x .095 tubing)

$13.95 each

#2929 3/4-16RH weld end (4130) – (for 1-3/8" x .095 tubing)

$13.95 each

#2930 3/4-16LH weld end (4130) – (for 1-3/8" x .095 tubing)

$13.95 each

#2931 3/4-16RH weld end (4130) – (for 1-1/2" x .095 tubing)

$36.50 each

#2932 3/4-16LH weld end (4130) – (for 1-1/2" x .095 tubing)

$36.95 each

#90-1 Lamb 4130 1-1/8" x .095" 4-link bar (including heliarc, full-length o.d. grind & right and left 4130 weld ends)

$69.65 each

#90-2 Lamb 4130 1-1/4" x .095" 4-link bar (including heliarc, full-length o.d. grind & right and left 4130 weld ends)

$78.87 each

#90-3 Lamb 4130 1-3/8" x .095" 4-link bar (including heliarc, full-length o.d. grind & right and left 4130 weld ends)

$95.00 each

Press Nuts, Reducer Bushings & Reducer Sleeves

#2975 3/8-24 Press-in nut

$5.40 each

#2975C 3/8-16 Press-in nut

$5.40 each

#2978 – Reducer bushing (.062" long) to reduce 1/2" to 3/8"

$4.10 each

#2979 – Reducer bushing (.125" long) to reduce 1/2" to 3/8", with a .125 shoulder - These are commonly installed into the side of the bearings in Koni shocks so that a 3/8" aircraft quality bolt may be utilized instead of a heavier 1/2" mounting bolt.

$4.10each

#2980 – Reducer bushing (.187" long) – to reduce 1/2" to 3/8", with a .187 shoulder

$4.10 each

#2981 – Reducer bushing (.250" long) – to reduce 1/2" to 3/8" with a .250 shoulder

$4.10 each

#2984 – Reducer sleeve – These are used to reduce i.d. of a rod end from 5/8" to 1/2"

$4.75 each

#2985 – Reducer sleeve – These are used to reduce i.d. of a rod end from 3/4" to 5/8"

$4.95 each

Differential Components

#2120A Lamb 9" pinion support (1-5/16" ball bearing)

$395.00 (assembly )

#2300 Lamb rear-end welding/installation fixture (48" long) - Comes complete with all components necessary to properly install Lamb Standard Housing Ends

$655.37

#2301 Lamb rear-end welding/installation fixture (60" long) - Comes complete with all components necessary to properly install Lamb standard Housing Ends

$725.00

Housing Ends and Related Components

Housing End I.D. Sheet

#2200 Lamb 4130 standard housing end (fits 3.150" o.d. x .825 bearing (pr)

$195.00/pair

#2200B Bolt & nut kit for pair of #2200 housing ends

$24.64/set

#2111 Lamb Bolt for #2200 Housing End

$2.25 (each)

#2209 Lamb axle bearing retainer (4130) – 45mm

$23.00

#2201 Lamb 4130 larger bearing housing ends - Includes (2) alloy retaining sleeves & (2) alloy spacers. (also required: (2) #CR22816 seal & (2) #6209DD NSK Bearing)

$229.00/pair

#2201A Lamb 4130 3.350 bearing housing ends - Includes(2) Lamb 3.350 bearing housing ends (2) alloy retaining sleeves (wedding rings), (2) alloy spacers (2) #CR22816 seal (2) #6209DD NSK Bearing)

$475.00

#2201-2 Lamb bearing retainer sleeve (wedding ring)

$25.00/ea

#2201B Lamb bolt kit for #2201 Housing Ends

$38.95

#2209 Lamb 45mm axle bearing spacer

$25.00/ea

Steering Components, Misc. Tools

#1A325 1/8" Vent/Breather

$4.95 each

#2800 Mitutoyo Digital Protractor, includes zippered carrying case

$225.00

#2825 Apex Steering U-Joint (3/4" i.d.; 7/8" o.d.) - You will need (2) of these to complete your steering assembly, along with the following hardware

$95.00 each

#2826 Apex Steering U-Joint Spline adapter

$28.50

#NAS1103-14 bolt (you will need two of these per steering U-joint)

$1.10 each

#NAS1291X3 Low-Height Flanged-Nut (you will need two of these per steering U-joint)

$.65 each

Service Fluid

#8002D Liter of Lubrication Engineering Synthetic Differential Oil (90 weight)

$16.00/liter

#870 Lamb Ultra-Low Friction Racing Synthetic Wheel Bearing Grease

$10.95/jar

#872 Wagner Dot 4 disc brake fluid (1 quart)

$6.95 each

Aircraft Hardware

Plated Steel Jam Nuts (used on rod ends, etc.):

#AN316-4R (1/4-28RH)

$.39 each

#AN316-4L (1/4-28LH)

$.74 each

#AN316-5R (5/16-24RH)

$.49 each

#AN316-5L (5/16-24LH)

$.79 each

#AN316-6R (3/8-24RH)

$.49 each

#AN316-6L (3/8-24LH)

$.79 each

#AN316-7R (7/16-20RH)

$.75 each

#AN316-7L (7/1620LH)

$1.02 each

#AN316-8R (1/2-20RH)

$1.22 each

#AN316-8L (1/2-20LH)

$1.75 each

#AN316-10R (5/8-18RH)

$3.75 each

#AN316-10L (5/8-18LH)

$4.95 each

#AN316-12R (3/4-16RH)

$7.25 each

#AN316-12L (3/4-16LH)

$7.95 each

#AN316-14R (7/8-14RH)

$6.95 each

#AN316-14L (7/8-14LH)

$5.99 each

#AN316-16R (1-14RH)

$5.25 each

#AN316-16L (1-14LH)

$8.50 each

#AN316-20R (1-1/4"RH)

$8.75 each

Stainless Steel Jam Nuts (be sure to lube these extra well to prevent galling):

#AN316C-8R (1/2-20RH)

$1.72 each

#AN316C-8L (1/2-20LH)

$2.21 each

#AN316C-10R (5/8-18RH)

$3.50 each

#AN316C-10L (5/8-18LH)

$6.13 each

#AN316C-12R (3/4-16RH)

$4.55 each

#AN316C-12L (3/4-16LH)

$6.30 each

Nylock-Lined Nuts:

#F52N7582-624 Full height 3/8" nut

$1.05 each

#F52NE720 Full height 7/16" nut (HT)

$1.55 each

#F52NE820 Full height 1/2" nut (HT)

$1.35 each

#F52NTE820 Low height 1/2" nut

$1.10 each

#MS21044N10 Full height 5/8" nut

$2.95 each

#F52NTE1018 Low height 5/8" nut

$3.95 each

Low-Height Flyweight Self-Locking Nuts:

#NAS1291X3 3/16" (cad plated)

$.65 each

#NAS1291X4 1/4" (cad plated)

$.75 each

#NAS1291X5 5/16" (cad plated)

$1.25 each

#NAS1291X6 3/8" (cad plated)

$1.30 each

#NAS1291-7 7/16" (dry film lube)

$7.25 each

12-Point Nuts:

#AJN12-1 3/8" ARP nut

$2.57 each

#APN12-1 7/16" ARP nut

$4.95 each

#ARN12-1 1/2" ARP nut

$3.92 each

Aircraft Bolts:
The following are common aircraft bolts. If you need others, please call as this is only a partial list:

#NAS1103-13 (3/16 x 13/16 grip) – used on steering U-joints

$1.10 each

#NAS1105-5 (5/16 x .312 grip)

$2.95 each

#NAS1105-8 (5/16 x �" grip)

$2.25 each

#NAS1106-6 (3/8 x 3/8" grip)

$2.10 each

#NAS1106-9 (3/8 x 9/16" grip)

$2.75 each

#NAS1106-10 (3/8 x 5/8"grip)

$3.45 each

#NAS1110-18 (5/8 x 1-1/8" grip) – commonly used on 4-link suspensions

$8.95 each

#NAS1110-20 (5/8" x 1-1/4" grip) – a little longer grip length for 4-link suspensions

$9.95 each

#NAS1110-23 (5/8" x 1-7/16" grip) – longer bolt used on 4-link suspensions

$9.95 each

#NAS1306-5 (3/8" x .312" grip)

$3.70 each

#NAS1306-9 (3/8" x .562" grip)

$4.95 each

#NAS1306-10 (3/8" x .625" grip)

$1.95 each

#NAS1306-11 (3/8" x .688" grip)

$2.75 each

#NAS1306-12 (3/8" x .750" grip)

$2.95 each

#NAS1306-14 (3/8" x .875" grip)

$2.95 each

#NAS1306-16 (3/8" x 1.000" grip)

$3.25 each

#NAS1306-17 (3/8" x 1.062" grip)

$3.45 each

#NAS1306-18 (3/8" x 1.125" grip)

$2.95 each

#NAS1306-20 (3/8" x 1.250" grip)

$4.50 each

#NAS1306-21 (3/8" x 1.312" grip)

$2.65 each

#NAS1306-23 (3/8" x 1.438" grip)

$3.95 each

#NAS1306-24 (3/8" x 1.500" grip)

$3.35 each

#NAS1306-28 (3/8" x 1.750" grip)

$3.70 each

#NAS1306-40 (3/8" x 2.500" grip)

$4.75 each

#NAS1307-7 (7/16 x .438" grip)

$3.95 each

#NAS1307-10 (7/16 x .625" grip)

$3.70 each

#NAS1308-20 (1/2" x 1.250" grip)

$9.25 each

#NAS1308-24 (1/2" x 1.500" grip)

$7.95 each

#NAS1308-26 (1/2" x 1.620" grip)

$14.50 each

#NAS1308-27 (1/2" x 1.688" grip)

$14.50 each

#NAS1308-29 (1/2" x 1.812" grip)

$14.50 each

#NAS1308-32 (1/2" x 2.000" grip)

$14.50 each

#NAS1308-36 (1/2" x 2.250" grip)

$15.50 each

#NAS1310-32 (5/8" x 2.000" grip)

$14.50 each

Aircraft Washers (standard thickness):

#MS20002-4 1/4" x .062" heat treated washer

$.07 each

#MS20002-5 5/16" x .062" heat treated washer

$.09 each

#MS20002-6 3/8" x .062" heat treated washer

$.09 each

#MS20002-7 7/16" x .062" heat treated washer

$.11 each

#MS20002-8 1/2" x .062" heat treated washer

$.11 each

#MS20002-10 5/8" x .062" heat treated washer (commonly used on 4-links)

$.31 each

Thin Washers (cad plated):

#AN960-416L 1/4" x .032" washer

$.04 each

#AN960-516L 5/16 x .032" washer

$.04 each

#AN960-616L 3/8" x .032" washer

$.04 each

#AN960-716L 7/16" x .032 washer

$.15 each

#AN960-816L 1/2" x .032 washer

$.22 each

#AN960-1016L 5/8" x .032 washer

$.29 each

[Home] [What's New] [Parts] [Order] [Repairs] [Terms] [About Lamb] [Contact Us]